Skip to main content

Sunday Sortie

This afternoon was a good time to move the Super X3 mill in its crate away from the door of the Tractor building so the 8N Ford could be put away. Once I remembered I have a perfectly good overhead lift which runs across the tractor bay, it was simply a matter of rigging a couple “straps” to lift the crate. The chains from Wal-Mart were ten feet long which was about three feet too short. Two chains and a towing strap later I was ready to give it a try. The crate lifted off the floor and was then pushed across the bay. This left room for the 8N Ford to return to the bay. Well, almost enough room. It is quite cramped in the bay now.

Soon I will have either a new worktable or a Harbor Freight mill stand #47599 to hold the Super X3 milling machine. You can see the little work room is a bit cluttered too. The X2 mill will go elsewhere, and the room will get cleaned up.

I am certainly happy the 1952 8N Ford tractor was able to lift the 420-pound crate with it attached to the middle location of the boom. That is one tough old tractor. It starts easily and does the work every time.

Tractor Boy

Popular posts from this blog

Farmall Cub Switch Replacement

It was a cold, wet, dreary day in Central Texas. Perfect weather in which to replace the light switch I replaced last week. The first replacement was blowing a 20-amp fuse in less than a second when turned to the farthest right position. Fortunately, I had added a separate fuse holder to the circuitry when the replacement did not have a fuse position. I spoke with the nice folk at Farmall Cub Forever and ordered a three position six-volt switch which arrived a few days ago. This time I took pictures so you can see what I was doing. Again, I replaced one wire at a time. The switch has a protrusion which fits in a notch in the console, and I replaced it so the two were properly aligned. I discovered it was easier to take the console off this time, and I did not need a small monkey to reach in the confined space.  I did; however, forget that I placed a piece of board between the hydraulic housing and the hood/fuel tank. So, when I started up the Cub to see how well it would run, there...

Farmall Cub greasing

Replacing gear oil and greasing the ’49 Cub ought to be a straight forward task(s). Well it hasn’t been. The transmission fluid was tan, looking like tan paint. Folks on Yesterday’s Tractor Farmall forum said it meant water had got inside the transmission. I wonder whether this tractor was under water at one time. I bought a Spectricide brand insecticide pump, put kerosene in it, and flushed the transmission, then refilled with 90 weight gear oil. The gear oil looked like and had the consistency of thin honey. Pic 1300 shows the transmission filler plug. A lot easier to reach than the plug for emptying the transmission. Note it has a square head. All of these plugs are square headed. Three and a half pints later, the transmission was back together. After the transmission, I decided to check the steering gear oil. It was not tan. It was black as could be so I flushed the housing with kerosene again and refilled with ¾ pint of 90 weight gear oil and replaced the filler plug. Pic 1301 s...

Farmall Cub carb and oil

The past few days I have been working on my Jan 1949 Farmall Cub tractor. I replaced the oil filter which was made of cardboard with one from NAPA with a metal body.  Pic 1264 shows the oil drain location on the right side of the engine. 1268 shows the oil drained, and 1269 shows the old oil filter. The oil was a bit dirty, but much, much cleaner than the black oil I drained from the 8N Ford. The oil filter reservoir cap needed cleaning and painting so I took care of that too. A dental pick was used to scrape off mu7ch of the dirt, followed by a small steel brush. Then a coat of primer and two coats of Farmall red made a pretty looking cap.   It is a good thing I have tools! A set of used dental picks, several small brushes, a cleaning tank, left handed drill bits, and finally a can of carburetor cleaned were all used to clean and restore the carburetor. Tractor Supply sells a kit for the IH carburetor on the 59 year old tractor. Pic 1261 shows the carburetor as removed ...