Skip to main content

Farmall Cub working

Believing the original four position light and charging switch was mostly worn out, I ordered a replacement from Farmall Cub Forever. Nice folks with whom to do business. Yesterday I braved the cold here in Central Texas to enter my Tractor Building and replace the old switch. First, I placed a block of wood between the hydraulic system and the hood/fuel tank to keep the fuel tank from collapsing onto something and maybe damaging the fuel bowl. Then I proceeded to remove four screws from around the top of the console and two bolts which fastened the console to the tractor body. Much easier to write than to do. There is very little room to move, and I do not have a trained monkey to reach in there and turn a wrench while holding something in place. It turned out to be much easier to remove the part than to replace it later, but I was blissfully naïve then.

The choke rod, the hydraulic rod, and the starter rod all had to be disconnected from one end or the other to allow room to move the console back far enough that I could get at the four-position switch. The wires were removed from the old switch one by one and fastened onto the new switch. Finally, I soldered appropriate ends on a replacement 20-amp fuse holder and then put the new switch were the old had been. The new switch had no fuse holder such as was on the original switch. It seemed prudent to add a fuse going between the same points as had been protected by the fuse in the first place.

Once I had the new switch in place it was time to replace the console on the tractor body and screw it to the hood. Here is where I needed two little monkeys to help me hold things in place and screw or bolt it all down. It took quite a while to complete. Then the three rods were refastened where they go. Time to try it out.

Oh, Oh. As soon as the switch was put in the fourth position (far right) I heard a tiny “tic” and the twenty-amp fuse was blown. After two more tries with the same result, I decided to avoid the fourth position and ask someone from the place where I bought it. I did that today and a three-position switch is on its way. These old tractors such as my ’49 Cub were modified over the years. It seems I do not need a four-position switch because I have a voltage regulator instead of the original “cut out”. I can say I got the lights to work. A final thing I did was to add hydraulic fluid to the hydraulic reservoir. From a new five-gallon pail, I pumped for quite a while until it began to flow out of the observation/filling hole. So today I started the tractor and ran it a bit to warm it, the worked the hydraulic touch control lever back and forth at least a dozen times. All is smooth hydraulically speaking. The Cub started immediately, and I fiddled just a couple minutes with the choke to get the engine running smoothly. It was forty degrees in that building and the Cub started within a couple seconds. As soon as I could get off the choke, I opened the sliding door, and we cooled down to 32 degrees. Brrr.

Tractor Boy

Popular posts from this blog

Farmall Cub Switch Replacement

It was a cold, wet, dreary day in Central Texas. Perfect weather in which to replace the light switch I replaced last week. The first replacement was blowing a 20-amp fuse in less than a second when turned to the farthest right position. Fortunately, I had added a separate fuse holder to the circuitry when the replacement did not have a fuse position. I spoke with the nice folk at Farmall Cub Forever and ordered a three position six-volt switch which arrived a few days ago. This time I took pictures so you can see what I was doing. Again, I replaced one wire at a time. The switch has a protrusion which fits in a notch in the console, and I replaced it so the two were properly aligned. I discovered it was easier to take the console off this time, and I did not need a small monkey to reach in the confined space.  I did; however, forget that I placed a piece of board between the hydraulic housing and the hood/fuel tank. So, when I started up the Cub to see how well it would run, there...

Farmall Cub greasing

Replacing gear oil and greasing the ’49 Cub ought to be a straight forward task(s). Well it hasn’t been. The transmission fluid was tan, looking like tan paint. Folks on Yesterday’s Tractor Farmall forum said it meant water had got inside the transmission. I wonder whether this tractor was under water at one time. I bought a Spectricide brand insecticide pump, put kerosene in it, and flushed the transmission, then refilled with 90 weight gear oil. The gear oil looked like and had the consistency of thin honey. Pic 1300 shows the transmission filler plug. A lot easier to reach than the plug for emptying the transmission. Note it has a square head. All of these plugs are square headed. Three and a half pints later, the transmission was back together. After the transmission, I decided to check the steering gear oil. It was not tan. It was black as could be so I flushed the housing with kerosene again and refilled with ¾ pint of 90 weight gear oil and replaced the filler plug. Pic 1301 s...

Uncle Phil Cause of Death

Phil was hit and killed by a drunk who was driving on the wrong side of the road and then left the scene of the collision. The man then hid in the nearby woods. Authorities found him, took him to a hospital, then he was arrested and jailed (in Vanderburg county) and is awaiting extradition to Wabash County. I hope he stays in jail until convicted. Uncle Phil was totally innocent, minding his own business. I have known Phil since he was fifteen years old. That is a long time, sort of.